Mild bowtie build

jpalmer

New member
Re: Mild bowtie build

I like this build. Hell if Alex can run 10's on L-35's, why couldn't you surpass that or match at least with Vortec's? I'll be looking forward to your progress.
 

n0mab00n

'Noma GT Fanatic
Re: Mild bowtie build

Any news/updates? Sucked to hear the bas news but I am interested to know what's going on with this .... might change my mind about doing a V8 in the SoGT :lol:
 

denny

Active member
Re: Mild bowtie build

Bottom end is finished.

IMAG0590.jpg

IMAG0588.jpg

IMAG0587.jpg

IMAG0585.jpg



Need to get on oil pan to fit and alos clear the caps.

Not sure the shop got the correct adaptor, it wont lined up to the stock pan.
IMAG0590.jpg

IMAG0589.jpg


Not of these is going to work without modification
, I am thinking it maybe eaiser to mod a 350 pan.
SU1HMDAwMTQtMjAxMTAzMTAtMTIyMi5qcGc.jpg
 
Last edited:

denny

Active member
Re: Mild bowtie build

Got my engine back from the engine shop, just have to find all the bolts and nuts I took off 9 months ago and see if I remember where they go.

SU1HMDAwNzUtMjAxMTA2MTktMjAyMy5qcGc.jpg


SU1HMDAwODAtMjAxMTA2MjAtMjE1MC5qcGc.jpg


SU1HMDAwNzEtMjAxMTA2MTktMjAxOS5qcGc.jpg
 

QuinnSY

Donating Member
Re: Mild bowtie build

Thats a good lookin motor you got there!
That oil pan sure looked like a pain though, but came out nice!
 

gt67sy

Member
Re: Mild bowtie build

That doesn't even look like the same pan looks like a sheet metal pan maybe from rpm
 

denny

Active member
Re: Mild bowtie build

Yes, thats a RPM pan. I didnt finished the moroso pan.
I have a total of 5 oilpans now, 4 for sale :)
 

denny

Active member
Re: Mild bowtie build

Few Issues I need to figure out.

#1 No dipstick, got a -6 fitting on the drain plug. The engine shop told I can connect a 6an flex hose and stick a dipstick in it.
SU1HMDAwODYtMjAxMTA2MjQtMDc1Ni5qcGc.jpg



#2 I want to have AC because I want to drive it in the summer, the facing intake is close to the tensioner (I have Mccoy Air2air)
SU1HMDAwODUtMjAxMTA2MjQtMDc1NS5qcGc.jpg


#3 I don’t think PF52 will not fit , what filter do use for on the block filter?
 

qbnkiller

Conflaguration Specialist
Re: Mild bowtie build

PF47...the filter for the 4-cyl S10's.

You can also take the pan off and have a shop weld an aluminum bung in it for a Lokar dipstick. ow is the time!

Looking sweet Denny!
 

denny

Active member
Re: Mild bowtie build

It never ends, engine in but the pan is leaking, its coming from the welds and not just one place.
I bought this pan as new from a board member not from rpm, I didnt pay cheap either $520, trying to find out where he got it from. I hate to have to pull the engine out.

I bought 2 pack of jb weld today - Fack!


SU1HMDAwOTQtMjAxMTA2MjYtMTEyNS5qcGc.jpg

SU1HMDAwOTUtMjAxMTA2MjYtMTEyNi5qcGc.jpg
 

denny

Active member
Re: Mild bowtie build

JB weld is holding up, alwayscode390 haven't return my pm on the oilpan.

see the bowtie
SU1HMDAxMjktMjAxMTA3MDktMTI0MC5qcGc.jpg



SU1HMDAxMzktMjAxMTA3MDktMTgyMy5qcGc.jpg


SU1HMDAxMzctMjAxMTA3MDktMTgyMi5qcGc.jpg



dipstick/drainplug
SU1HMDAxMzQtMjAxMTA3MDktMTI0NC5qcGc.jpg
 

gt67sy

Member
Re: Mild bowtie build

So I saw you drilled your Bowtie block for oil returns up in the lifter valleys is that somethIng that is recommended for these Bowtie blocks? Haven't read or seen anything about it till I saw you did it and i have the same Bowtie block going to the engine builder this week and am wonder if I should have him do it?
 

denny

Active member
Re: Mild bowtie build

So I saw you drilled your Bowtie block for oil returns up in the lifter valleys is that somethIng that is recommended for these Bowtie blocks? Haven't read or seen anything about it till I saw you did it and i have the same Bowtie block going to the engine builder this week and am wonder if I should have him do it?

Not sure, my engine builder dit that. The one drain hole it have is high up, you probably have 1qt oil sitting up there before it start drainig down.
 
Top