Mild bowtie build

denny

Active member
Bowtie block, steel crank, eagle rods (L19 bolts), wasco custom piston, vortec heads.
+
BS3, 4l80E, ATR headers with turbonetics T72

lots of pic

Heads re-work,
IMG_0560.jpg


IMG_0559.jpg


IMG_0558.jpg


IMG_0557.jpg


IMG_0556.jpg


IMG_0555.jpg


IMG_0554.jpg













l
 

Syborg Twin Turbo

Syborg Twin Turbo
Re: Mild bowtie build

Not sure, I bought the crank here on the fourm, that person bought it from someone else. I think its from crankshaft specialist in Texas, maybe.

Hi Denny

How did the crank balance out. I know some of them needed a bunch of weight / other didn't .

ps - subscribed
 

denny

Active member
Re: Mild bowtie build

Hi Denny

How did the crank balance out. I know some of them needed a bunch of weight / other didn't .

ps - subscribed

I don't believe the crank is balance yet, the engine builder is waiting on the piston.


BTW- the engine is being built by Lab Engine Specialists in Lindenhurst NY.
 

denny

Active member
Re: Mild bowtie build

Not much progress in the last 2 months..

Got the wesco pistons, needs to be sent for coating
CIMG1791.jpg


Drilled oil return holes from the valley
CIMG1789.jpg

CIMG1790.jpg
 

denny

Active member
Re: Mild bowtie build

Hi Denny

How did the crank balance out. I know some of them needed a bunch of weight / other didn't .

ps - subscribed


the shop had a hard time balancing the crank, like 4 mallory weight and still had to go with a 454 damper and flexplate
 

denny

Active member
Re: Mild bowtie build

The block needed a lot of work.

The bearing was problem because the journals on the crank is not square at the corners. The builder is still uspset that I bought this crank, there were so much work had to be done to it.
I dont remember half of what the builder is saying to me, all I hear and see is $$$$.

I am planing on putting on an accusump, don't want to mess this engine up

Got the pistons and coated, top and side.
utf-8BSU1HMDA1NDktMjAxMTAyMTItMTIxMi5qcGc.jpg

utf-8BSU1HMDA1NTAtMjAxMTAyMTItMTIxMi5qcGc.jpg

utf-8BSU1HMDA1NTQtMjAxMTAyMTItMTIxMy5qcGc.jpg

utf-8BSU1HMDA1NTEtMjAxMTAyMTItMTIxMi5qcGc.jpg

utf-8BSU1HMDA1NTItMjAxMTAyMTItMTIxMi5qcGc.jpg

utf-8BSU1HMDA1NTMtMjAxMTAyMTItMTIxMy5qcGc.jpg

utf-8BSU1HMDA1NTQtMjAxMTAyMTItMTIxMy5qcGc-1.jpg
 

denny

Active member
Re: Mild bowtie build

BTW - I am going to an on block oil filter and ditching the remote filter.
 

It's just a six

Super Member
Re: Mild bowtie build

Not trying to be an A$$.

Are the pistons Wiseco? http://www.wiseco.com/

You are using Vortec cast iron heads?

I would use some other aluminum heads, if those are Vortecs,that's what will be limiting your power output.Aluminum heads can allow to run higher compression also.:2cents:

Nice build on the other items.:tup:
 

denny

Active member
Re: Mild bowtie build

Not trying to be an A$$.

Are the pistons Wiseco? http://www.wiseco.com/

You are using Vortec cast iron heads?

I would use some other aluminum heads, if those are Vortecs,that's waht will be limiting your power output.Aluminum heads can allow to run higher compresion.:2cents:

Nice build on the other items.:tup:


typo - yes , wiseco I don't think there is a wasco :)

I thought about aluminum heads but money is the factor.
complete ported heads and custom headers thats another 5k.
Then more power means I have to upgrade everything else, fuel, rearend , suspension and so on. It will never end.
 

denny

Active member
Re: Mild bowtie build

wait - "MILD BOWTIE BUILD"
now if I get aluminum heads then it wouldnt be, no?
 
Top