Search results

Long story short...the mechanic broke one of the center cap locks so I need a new set. Does anyone know what size I need to order? Truck is not even here because it is at the body shop getting a tab repaired on the cladding that the mechanic broke. No mechanic jokes please! It is still a touchy...

CEL came on after installing aftermarket gauges (water temp, oil press., boost). Code 15 Coolant temp sensor. I have a gentleman doing the work for me and he used the new water temp sensor/sending unit in the original one's location and hooked it up and left the original dash gauge unhooked...

Looking for a center cap wheel lock. If you have one laying around I sure could use one. You can text/call me directly at (217)454-2484. Thanks, John

Is there any noticeable performance benefit to using Eric's chip on a stock motor? I'm wanting to keep the truck stock if possible, but am wanting a little extra performance. I'm not 100% opposed to larger injectors, AFPR,etc. if the boost needs turned up a few lbs.. Thanks

I have a broken drivers side motor mount....what needs removed to replace it?? Or maybe a special tool to help....Thanks!

Hi everyone, while doing routine maintenance on my truck, I noticed a substantial crack in my air intake tube (the one that is partially above the radiator) from turbo to air box. Hoping someone has one they could spare reasonably priced...maybe somebody that switched to CAI. Thank you.

Im looking for the stock air tube that connects from the turbo and the air cleaner assembly. Its the tube that runs above the radiator about the width of the engine. PM me if you have one that you could part with. Thanks

I am in the process of gathering parts for my upcoming LoTek 3 gauge A pillar setup and have acquired the pillar pod as well as the gauges. I'm trying to have all the parts needed on the bench when I go to do this, and have a question as to what additional fittings are needed to install the...

Did the Typhoons have keyless entry? I bought my truck several years ago and just received an ignition key and a door lock key. If they are available where do I buy one and more importantly how do you program them? Thank you,

If you register with Advance Auto Parts (which takes less than 5 minutes) there's an awesome discount code. The code is TRT41 and it instantly takes $40 off your order of $100 or more. I ordered some Autometer gauges and was actually able to use the code twice on my same email, so essentially I...

WTB Drivers power window switch and the power door lock drivers door for a 93 Ty.

Does anyone know the part number for the Autometer 3 gauge pillar pod? I found the 86-93 S10 part number but unsure if they are the same. Suspect they are but trying to get verification. Thanks

I realize that you can safely run more boost with a meth kit, not really wanting to go that route though. How much boost can I SAFELY run on a good running truck without meth? Going to have Turbo Tweak burn me a chip, and I plan on an AFPR as well. Should I use a 2 bar or 3 bar map? 2 bar is...

Does anyone know if the Accel AFPR 74750 is the correct part number for our trucks?

Both are stock. Advertised quarter mile times are 13.3 for the 2008 SRT8 and 14.5 for my 93 Ty. What mods would I have to do to beat the SRT8 in the quarter mile?

Couldn't find much on the web, but I'm hoping I can get help here. Not wanting anything too obnoxious, truck is stock. Im looking for a deep tone and I read somewhere that you have to be careful on what you put on cause the wrong muffler will cause turbo spike. Sound bytes greatly appreciated...

Owner of a bone stock 93 Typhoon.....understand I can gain quite abit of performance with a few bolt ons and a nice tune. Looking for a good tuner in Illinois or surrounding. I live in Mt. Zion (62549) but am willing to travel. Thanks

Just wanting to verify the part number prior to ordering. Showing Auto Meter part 17114 (86-93 S-10 Truck). Is this the correct one? Thanks in advance.

I have a 1993 Typhoon and am looking to put a set of new wheels on my truck, however I know that the truck has different offsets front and rear, any suggestions? Is there any spacers/adaptors avaliable that people are using and can you send me a link. Thanks for your help .......I have a set of...

Been awhile since I've been at this site, but I wanted to get everyone updated on the truck. Had a new trans installed last fall. Searched and found the cladding that I needed that was either missing or broken. Took it to the body shop where it's been ever since. Over the winter I viewed it as...