wtf, got stock memcals

88GTZ

Donating Member
I got some stock memcals from a member and the truck won't run with them, WTF I'm pissed haven't heard back from the guy... It doesn't run too bad with the kenne bell chip, but the idle is weird... Any suggestions guys, need help... my truck has docs that says it has the 32lb injectors, is there any way it won't run with the stock memcals?!?!?!?
 

Quickstop [UK]

Combating adversyty.
Re: wtf, got stock memcals

What MAP have you got? 2Bar or 3 Bar? Stock is 2 Bar, 3 Bar MAP would cause issues amongst other things.

Whate are your other mods, suspected or known?

Merry Christmas!
 

88GTZ

Donating Member
Re: wtf, got stock memcals

I assume its a stock map, other mods kb afpr, kb a2a,kb cold air, underdrive pulley....

Thanks for the quick reply...

Merry Christmas
 

TYTILIDIE

METH HEAD
Re: wtf, got stock memcals

Some people may tell you that the truck "shouldn't" run bad with 32's on the stock chip but mine did. It ran awful. The 32's made a huge difference in my Ty with the tune though. If I were you, I'd either work on a tune, learning to tune or a set of stock injectors to match your stock chip.

More info on the truck would also help, what MAP(positive ID) turbo, what is your FP set to?
 

88GTZ

Donating Member
Re: wtf, got stock memcals

I guess I'll start researching tunning, I would like to leave the 32's... The turbo is stock, dp stock, cat stock, 3" cat back, fp I think is 50 at idle but I'll double check (think I researched that).... Thanks for the replies
 

TYTILIDIE

METH HEAD
Re: wtf, got stock memcals

50 at idle is too high. Should be 42 or so.

Not sure if it is an altitude thing but every truck I have seen up here needed to be at at least 48psi to run normal. When on a stockish truck anyway. So 50 may not be off. You could try lowering it and see it runs but I doubt it will be any better.

Do you have Datamaster?
 

BoostedSUV

Active member
Re: wtf, got stock memcals

50lbs at idle with the vac line off isn't so bad... if it's 50lbs with the vac line connected I would lower it.
 

88GTZ

Donating Member
Re: wtf, got stock memcals

I don't have a datamaster, I'll play around with fp and see what it does.... Got a datamaster 4 sale?
 

dgoodhue

BuSTeD 4.3
Re: wtf, got stock memcals

Stock fuel pressure is around 42-44 psi with the vacuum line off an plugged. I would set it that as base line. What are the number & letters on the Memcal that you can see through the openings?

32# injectors are only slightly larger than stock 30#'s. Not all injectors have the same flow rates throught the fueling curve, so it can make a big difference in part throttle driveability.
 

bundie

New member
Re: wtf, got stock memcals

with those mods go for a tune...otherwise you will get overboost on a stock chip
 

88GTZ

Donating Member
Re: wtf, got stock memcals

Memcal # delco AMDB 8370... I've seen my aftermarket boost gauge at 16psi a couple times, just 4 a second though...I got a laptop, I'll scrape up some dough and get a datamaster... A member on here test drove my truck and put a datamaster on it, he said it did good but didn't specify any details
 

Poconojoe

Donating Member
Re: wtf, got stock memcals

That chip is for a 2.3 in a 1988 Cutlass or Gran Am with stick shift, with California emissions, using a service number 01227749 ECM. The GM part number for it is 16088369
 

88GTZ

Donating Member
Re: wtf, got stock memcals

I got it from a member here from cali, no wonder why it wouldn't run. I can't believe my 1st part experience on here is going to be shitty...I've txt him and he won't reply, guess I just wasted my money on that. Also where can I pick up a cable
 

Poconojoe

Donating Member
Re: wtf, got stock memcals

I got it from a member here from cali, no wonder why it wouldn't run. I can't believe my 1st part experience on here is going to be shitty...I've txt him and he won't reply, guess I just wasted my money on that. Also where can I pick up a cable

The guy might not have known what it was from, of course, he shouldn't have sold it as a Sy / Ty chip, if he wasnt sure. I have software to check the BCC (BraodCast Code) to see the spplication and if there were any revisions.
As far as a cable I buy most of my stuff from Craig ( www.Moates.net ) He's a great guy to deal with and also he supports our comunity, by suppling give away stuff for the nationals and other events. I used Craig for tuning stuff long before I bought my Sy, so it was natural to go to him, for my Sy tuning stuff
 

TYTILIDIE

METH HEAD
Re: wtf, got stock memcals

I got it from a member here from cali, no wonder why it wouldn't run. I can't believe my 1st part experience on here is going to be shitty...I've txt him and he won't reply, guess I just wasted my money on that. Also where can I pick up a cable

Leave him a bad feedback. For some reason people around here are afraid of that.
 

TYTILIDIE

METH HEAD
Re: wtf, got stock memcals

As far as FP goes, I have mine set at 48 with vacuum line ON. If I go any less, it doesn't run right. My Ty was like that, Abe's Ty was like that, Austin's Sy was like that, my wife's Ty is like that. Don't be afraid of 50psi up here.
 

88GTZ

Donating Member
Re: wtf, got stock memcals

I'm not saying he sold them knowing they we're not sy/ty memcals, but he shouldve checked before selling them, and why won't he get back to me? I hate throwing money away but it seems like I did on this deal, also is there any way to find out if the superchip I got from him is the right one? Thanks for all the replies, I'm down in new mexico this week when I get back I'll play with fp and see what it does
 
Top