ultimate=slow spool & low boost

heavy breather

FBI enforcer
Last weekend I dove into some serious work on the TY. I changed map sensors and went to an ultimate. The idle is great, and no C.E. lights. But, I am never seeing more than 10lbs of boost. And, the spool is the slowest I have ever seen. I am thinking I got the wrong map. Any suggestions?

When I hit 0 vacuum The stock gauge is pegged at 15lbs. I thought it wouldn't move past 0.

I also have a mild "tip-in" stumble. It happens on take-off and cruise to accel.

I was also thinking vacuum hose, but I have a solid 18lbs at idle.
 

GM TURBO

Sell Out
Re: ultimate=slow spool & low boost

heavy breather said:
When I hit 0 vacuum The stock gauge is pegged at 15lbs. I thought it wouldn't move past 0.


I was also thinking vacuum hose, but I have a solid 18lbs at idle.

You shouldn't see much over 0 on the stock gauge.

18# at idle - sounds like your truck just entered the Twilight Zone. You're making boost without doing anthing.

I would guess MAP - ID TEN TEA Error maybe.

What does Datamaster say? Did you change the calibration on DM to go from 2-bar to 3-bar? Did you use a AC Delco MAP.
 

Tooky

Serious about performance
When I got my 3 Bar MAP sensor it had the GM Part number on a sticker right on the sensor itself. Does yours? I got mine about 6 months ago, I imagine their stock would still be the same.
 
i dont believe the oem boost gauge should ever go positive with the 3 bar - sounds like u got hte wrong map.
post your part number.
 

Hu Ryde

Donating Member
Make sure your PN is same as this 3 Bar: GM #16040749 and did you use the OEM stock chip or the one that was in it before?
 

SY2932

Administrator
The part number for the stock 2 bar MAP sensor is 16009886. The socket where the plug plugs into is orange in color.

The part number for the 3 bar MAP sensor is 16040749. The socket is *red* where the plug plugs into if I remember correctly. My truck is at home or else I would go out and look. HTH's

Mike Campbell
 

Hu Ryde

Donating Member
SY2932 said:
The part number for the stock 2 bar MAP sensor is 16009886. The socket where the plug plugs into is orange in color.

The part number for the 3 bar MAP sensor is 16040749. The socket is *red* where the plug plugs into if I remember correctly. My truck is at home or else I would go out and look. HTH's

Mike Campbell

Both of mine where all black.............?????????
 

SY2932

Administrator
Yes, they are all black on the outside. You have to look into the socket (turn the MAP sensor so the downside is facing up) where the plug plugs into to see the colored insert. HTH's

Mike Campbell
 

Hu Ryde

Donating Member
SY2932 said:
Yes, they are all black on the outside. You have to look into the socket (turn the MAP sensor so the downside is facing up) where the plug plugs into to see the colored insert. HTH's

Mike Campbell

Ahh, I see says the blind man. No, really, I do. Ok, I'll stop now.
 

SY2932

Administrator
Hey Jesse, while you're tweakin' and peekin' why don't ya confirm if the 3 bar is red in color or not :wink: ?

Hey, i forgot to give you a "donation" at the meet for syty.huryde.com ... Gimme your mailing addy and I'll send ya a few bucks :D .

Mike Campbell
 

Hu Ryde

Donating Member
I can't confirm the color. Truck has been put away for school. Sorry.

Check your PM!
You Rock!!
 

bdubb

I am teh kingpin!
3 bar weather pack connector is black on the under side.

stock 2 bar, is red/orange color.
 

bdubb

I am teh kingpin!
you're gauge cluster can still see boost with a 3 bar, i know mine does.

and i know my buddy Jim old typhoon, he made the stock cluster work with the 3 bar.
 

Daron

Active member
My Stock gauge will also go above "0" under boost using the 3 bar. Have you fixed the prob, Heavy?
 

Ian Turgeon

Cascading Inspiration
just to back up the others, yes, the stock gauge will go above 0, I dont know the exact numbers, but roughly 0# is now at the -5 mark, and add ~5# per line above that
 

heavy breather

FBI enforcer
18# at idle - sounds like your truck just entered the Twilight Zone. You're making boost without doing anthing

What I meant was 18inches of vacuum. Per boost gauge

As far as the map it is a Standard Ignition Parts piece. I was doing the work at a local dealership, parts closed at noon and they couldn't get me one in time, so I got one from Advanced.

Do the barbs inside the weatherpack match up on the 3 bar? I had to scrape these out with a screwdriver, because they wouldn't match up. One was already gone, but the other would not allow me to pluge the connector in securely.(?sp?)

I am not getting any misfire or anything when the truck is under boost, but there is like no spool. Ten pounds is max boost and it feels like a slug. I guess I'll get a GM map today, and try that.

BTW Jesse, I nailed down the break up at 3K. It was a bad coil. The electrode looked like someone hit it with a cutting torch.
 

Daron

Active member
heavy breather said:
18# at idle - sounds like your truck just entered the Twilight Zone. You're making boost without doing anthing

What I meant was 18inches of vacuum. Per boost gauge

As far as the map it is a Standard Ignition Parts piece. I was doing the work at a local dealership, parts closed at noon and they couldn't get me one in time, so I got one from Advanced.

Do the barbs inside the weatherpack match up on the 3 bar? I had to scrape these out with a screwdriver, because they wouldn't match up. One was already gone, but the other would not allow me to pluge the connector in securely.(?sp?)

I am not getting any misfire or anything when the truck is under boost, but there is like no spool. Ten pounds is max boost and it feels like a slug. I guess I'll get a GM map today, and try that.

BTW Jesse, I nailed down the break up at 3K. It was a bad coil. The electrode looked like someone hit it with a cutting torch.

The connection for the MAP from the stock harness should plug right into the 3bar, no mod needed. Sounds like you have the wrong MAP in there...
 

sytyguy

Moderated User
FWIW, Standard Motor Company does NOT make a 3 bar MAP. I sell Standard and have been back and forth with their tech dept about making a 3 bar MAP. They do not and will not make one due to low demand (other than TTAs and a handful of other highly modified GMs, we're the only ones using them). They make stock 2 bars all day long, but no 3 bar. BTW, they (Standard) do not color code they're connectors, so using that as a reference is not reliable....for GM it is however.

So.....if you do, indeed, have a Standard MAP sensor (AS6 I assume) in there with a 3 bar Ultimate, it will not work. Get a genuine GM 3 bar MAP and all should be well.

BTW, did you tell the guys @ Advance/Discount that you wanted a 3 bar (or stock MAP for TTA)? It's doubtful anyone there would know what a 3 bar is, and if someone claimed they did and gave you that one, then there's no telling WTF they gave you. :wink:

Michael
 

SY2932

Administrator
As far as the map it is a Standard Ignition Parts piece. I was doing the work at a local dealership, parts closed at noon and they couldn't get me one in time, so I got one from Advanced.

Do not pass GO, do not collect $200. Go directly to jail :wink: ! If you had to modify that sensor in anyway you definitely have the wrong one. Get the right one it there and get ready to run like a raped ape :D !

Mike Campbell
 
Top