Steering Upgrade part #'s

jjorgensen52

NHSTE - I'm the only one!
Since I had a request for these, I thought I'd post the parts I used to upgrade my steering system. It's real tight, 1.5 turns lock to lock and 0 slop :tup:

-AGR Quicksteer box, 12:1, triple bearings, 6061-T6 caps, Summit #AGR-225153 - $329.95
-AGR Superpump Saginaw P-series Metric, high flow, Summit #AGR-807256 - $149.95
-Borgeson steering shaft, 14", 3/4" - 36 spline, aluminum, Borgeson #AL736X14X2 - $20
-Flaming River Ujoints, Stainless steel needle bearings: #FR2514DD 1" DD X 3/4"-36 - $89.50
#FR2524 /4" -30 X 3/4" -36 -$89.50
-Used Moog second style pitman and idler arms, Moog tie rods and Moog sleeves ~$320... should have used the Edelbrock solid sleeves, but oh well :roll:

IMG_1208.jpg
 
Last edited:

jwaller

Evil Genius/SyTy Guru
Re: Steering Upgrade part #'s

just wondering why you didnt use the borgeson SS joints? they look identical to me.
 

jjorgensen52

NHSTE - I'm the only one!
Re: Steering Upgrade part #'s

jwaller said:
just wondering why you didnt use the borgeson SS joints? they look identical to me.
Mostly because I could get ahold of the Flaming River joints more easily... other than that, no real reason. :roll:
 

Jer

Don't taze me bro!
Re: Steering Upgrade part #'s

Do you have the cost breakdown for the parts list?
 

jjorgensen52

NHSTE - I'm the only one!
Re: Steering Upgrade part #'s

yeah... this is sort of the expensive rout, but well worth it if you can pony up the cash :tup:
I'll add it to the original post
 

HighPerformanceTrucks

Lift & Shift Specialist
Re: Steering Upgrade part #'s

I would seriously consider converting to a colapse style steering shaft for added safety in a hard front end accident.
 

jwaller

Evil Genius/SyTy Guru
Re: Steering Upgrade part #'s

ivanko barbell said:
I would seriously consider converting to a colapse style steering shaft for added safety in a hard front end accident.

I was ganna say the same thing but I see he did it in alum, and I dont think they have alum in that style. but I would give up those style points so I wouldnt eat the steering wheel in event of a crash.
 

HighPerformanceTrucks

Lift & Shift Specialist
Re: Steering Upgrade part #'s

jwaller said:
I was ganna say the same thing but I see he did it in alum, and I dont think they have alum in that style. but I would give up those style points so I wouldnt eat the steering wheel in event of a crash.

I thought aluminum was not recommended for street use?
 

jjorgensen52

NHSTE - I'm the only one!
Re: Steering Upgrade part #'s

I didn't see anything about not for street use... they did have a fair deal of stuff about how 3/4" is absolute minimum to meet OE strength in aluminum... I think that shaft would bend pretty easy in a hard front ender
 
Re: Steering Upgrade part #'s

Nice parts list. Ill have to redo my new Ty this way in the near future.


Also, on the shaft you used a 14" splined on both ends shaft,but did you have to shorten the shaft at all or did it go in as is?
 
Last edited:

jwaller

Evil Genius/SyTy Guru
Re: Steering Upgrade part #'s

I wouldnt bet on the alum bending, is it hollow or solid? reason I say is bc I've had many sterring shafts out and it didnt take much to start pushing the collum up into the firewall.
 

jjorgensen52

NHSTE - I'm the only one!
Re: Steering Upgrade part #'s

HotRodV6 said:
Nice parts list. Ill have to redo my new Ty this way in the near future.


Also, on the shaft you used a 14" splined on both ends shaft,but did you have to shorten the shaft at all or did it go in as is?
I had to trim it about 3/4" ... I think ti ended being 13.21" or something
It's a solid shaft waller
 

vinnieTy

TY # 1889
Re: Steering Upgrade part #'s

Okay so these items is what i will need to get rid of all that play in my steering wheel. I just bought my ty and dam the steering is one thing i need to get use to but if i can tighten it up i would prefer to do that. Any one else have any comments or suggestions on this matter.


thanks guys
 

dgoodhue

BuSTeD 4.3
Re: Steering Upgrade part #'s

Basically to tighten up the steering, you need look into replace the parts that wear or loosen. Tie rods, Idler Arm, Pitman Arm, Steering Box, and Steering shaft. The above poster used basically new parts, but many use Zq8 steering boxes, because they can be found used and for $100-$125. On high mile vehicle, sometime the steering columns u joint also sometime is worn.

If I had to rebuild a sloppy steering, I would do the tie rods, idler arm and steering shaft first. Then the steering box and Pitman arm. You should be able to rebuild the whole system for around $500-600 in parts...
 

vinnieTy

TY # 1889
Re: Steering Upgrade part #'s

Any recommendation on where to order these parts. I see alot of people using summit racing, i never used them before but have heard of them. Any other companies or is summit the way to go.
 

jwaller

Evil Genius/SyTy Guru
Re: Steering Upgrade part #'s

I sell the entire borgeson shaft and you can get all the front end parts from michael at tucker auto.
 

mmp142965

say it like you spell it!
Re: Steering Upgrade part #'s

vinnieTy said:
Any recommendation on where to order these parts. I see alot of people using summit racing, i never used them before but have heard of them. Any other companies or is summit the way to go.

Summit is a good place to get the AGR steering box and pump. X2 what waller said for everything else.
 

#2875

built, not bought
Re: Steering Upgrade part #'s

FYI my NEW agr steering pump gushed fluid on my out of the front seal onto my x-pipe after 0.000 miles. summit replaced it (mainly because i spend half my paycheck with them) but i put a stock pump back in because that kind of thing really pisses me off.

there are mixed feelings on this but i personally really like my steering stabilizer. you just need a 4X4 link: $25 or free if you live close to WV like me.

also, zq8 boxes litter junkyards... NOT HARD TO FIND: $50.

vinnieTy said:
Any recommendation on where to order these parts. I see alot of people using summit racing, i never used them before but have heard of them. Any other companies or is summit the way to go.

you can buy the steering pump from me. never used or even taken out of box. NO WARRANTY ON THAT OVERPRICED POS THOUGH !!!!!!!
 

#2875

built, not bought
Re: Steering Upgrade part #'s

yes but you can also buy a ubolt kit that will do the same thing. i think the kit i saw had a rancho sticker. i don't have a p# though. i will have to think about the pump, will pm you later (going on vacation) but you have first dibbs.
 
Top