Briank
New member
Hi guys, I am new to this forum. Lot’s of good information here. I look forward to meeting some of you at Bandimere this year. I hear there is a lot of SY/TY here in Colorado. Maybe we could do a Hooters meet some time at 120th Ave in Westminster.
I am in a local SRT club and we do meets there sometimes. I get half the patio and the manager lets us park some of the cars on the side walk. Cool setup.
I bought my Syclone 1310 back in October 2010. It took me a few months to find one in great shape at a descent price. I did not want anything that needed body work. I found it in Colorado Springs. The truck had 28,348 miles and second owner with a clean car fax and ran great. Now it is has 31,000 miles. I have spent some money on the truck getting it right for me. The front end was squeaky over bumps and steering was not right. So I spent some time working on it. Here is my part list and pictures.
29,963 New spark plugs/ wires
29,963 New rotor and Distributor Cap
29,643 New oil and filter mobile 1
29,963 Flush Radiator twice
29,963 Flush Intercooler cooler radiator
New oil pressure switch
New water temperature Gauge sending unit
New Belt teenier
New belt pulley
New Vacuum lines on the motor
29,988 New transmission filter/fluid and gasket
29,988 Transfer /Front/Rear diff oil
New tires
New wheel lock bolt and key for hub caps
syliver star head light
New turn signal lever (letters fadded)
Rear trans Seal
Data Master logger with laptop (craigslist)
Custom boost gauge
Ultimite chip 16-1 3 bar not installed
All new front suspension Rubber stops, Ball joints,Control arm bushings,Idler arm, Pitman arm, Inner/outer tie rods, Center Link to add steering stabilizer shock. Heavy duty adjuster sleeves, Seal steering knuckle 2x,
Inner fender seal- LH
Inner fender seal- RH
New Door Window seal outer Seal L/R
Windshield Trim
Hood Hinge seal-LH
Hood Hinge seal-RH
New window guild clips
Cap- overflow tamk
Radiator Cap
I am in a local SRT club and we do meets there sometimes. I get half the patio and the manager lets us park some of the cars on the side walk. Cool setup.
I bought my Syclone 1310 back in October 2010. It took me a few months to find one in great shape at a descent price. I did not want anything that needed body work. I found it in Colorado Springs. The truck had 28,348 miles and second owner with a clean car fax and ran great. Now it is has 31,000 miles. I have spent some money on the truck getting it right for me. The front end was squeaky over bumps and steering was not right. So I spent some time working on it. Here is my part list and pictures.
29,963 New spark plugs/ wires
29,963 New rotor and Distributor Cap
29,643 New oil and filter mobile 1
29,963 Flush Radiator twice
29,963 Flush Intercooler cooler radiator
New oil pressure switch
New water temperature Gauge sending unit
New Belt teenier
New belt pulley
New Vacuum lines on the motor
29,988 New transmission filter/fluid and gasket
29,988 Transfer /Front/Rear diff oil
New tires
New wheel lock bolt and key for hub caps
syliver star head light
New turn signal lever (letters fadded)
Rear trans Seal
Data Master logger with laptop (craigslist)
Custom boost gauge
Ultimite chip 16-1 3 bar not installed
All new front suspension Rubber stops, Ball joints,Control arm bushings,Idler arm, Pitman arm, Inner/outer tie rods, Center Link to add steering stabilizer shock. Heavy duty adjuster sleeves, Seal steering knuckle 2x,
Inner fender seal- LH
Inner fender seal- RH
New Door Window seal outer Seal L/R
Windshield Trim
Hood Hinge seal-LH
Hood Hinge seal-RH
New window guild clips
Cap- overflow tamk
Radiator Cap
