Killed a loaded 306 mustang

Tonight was my first actual kill with another car thats not a ricer.

To start off the story... I was walking to class and this guy in a ugly early 80s model mustang pulls up and revs the engine. It sounded mean... So i yelled out "Hey, wanna race?" and the guy laughed. This made me furious. :evil: I keep asking around campus if anyone knows what he has done to his car. no one knows.

back to tonight... I was driving down the hwy and here he comes. i didnt recognize him at first but that exhaust was unforgetable. we roll down the windows and i say "now do you wanna race?" he said sure. light turned green before i could prep the boosted launch so i launch at 0psi. we are neck and neck. all the way up to 70. then we shut it down b/c it is a 40 mph speed limit. then we do it from a roll at 35 which sucks. same results. Then the time came and i wanted a red light. BINGO. I get the launch ready any launch at 7psi and all i see is fishtailing in the mirrors and headlights getting smaller.

we pull over into the walmart parking lot and start talking. he said that he has the 306 5.0l in his w/ high-performance interals everything you can think of from pistons to rockers to bore to cams. he said he runs a 13.9 @ 110. and i said im stock and run 13.3 @ 99-ish. he was amazed.

It felt good beating something that had tons of mods and im 99% stock execpt k&n. :D Sorry for the long post.
 

Flyin Ryan

hated cuz he drives fords
I agree great job of putting someone in there place but come on a 13.9 in a built up 302 car? that's weak the guy must have been bsing you or just didn't know anything about driving.. in any event great kill :tup:
 
yeah it kinda seemed like high times. he told me all he does was peel out all the way through first and second. i dont think he knew how to drive it well. thanks for the props.
 

Syclone Rob

Its all ABOOT the SYTY eh
hahahaha a built 302 goes 13.9..... :eek: come on.... My buddies 5.0 goes 12.9 with edelbrock heads, 1.6 rr, trickflow intake, can't remember the mass air meter size, Ecam,Underdrive pulleys and full mac exhaust!! Gee, this guy is seriously feeding you the BS or he just plain and simple can't drive.. :-?
 

syco 2

New member
with a good driver that guy should see high 11s my stang went 11.50s stock bottom end all motor. i got a friend thats going 11.80s with out a dyno tune and ported ford explorer heads all motor stock bottom end. any ways a mid 12 sy took out my stang on the street up to 80 and it pulls the left front a half foot off the ground on the street im proud to say that though. cause simply syclones rule.
 

Loeryder

New member
if he said "peel out all the way through first and second" I doubt he knows wtf hes talking about or how to drive one ofr the other.

Of all the car guys I know everywhere none of them use the term peel out to describe lack of traction due to horsepower.
Peeling out is what you do in your 4 banger or your big wheel.


Anyhow, nice kill.
It feels alot better when they are worthy opponents, eh?
 

Drac0nic

New member
sy#276 said:
with a good driver that guy should see high 11s my stang went 11.50s stock bottom end all motor. i got a friend thats going 11.80s with out a dyno tune and ported ford explorer heads all motor stock bottom end. any ways a mid 12 sy took out my stang on the street up to 80 and it pulls the left front a half foot off the ground on the street im proud to say that though. cause simply syclones rule.

Explorer heads? My curosity is piqued. Nice K btw.
 

SY2932

Administrator
Syclone Rob said:
hahahaha a built 302 goes 13.9..... :eek:

Got that right, my coworker's 302 powered 'stang has ran a best 13.45 @ 98 MPH at Norwalk and it's practically stock...
 

blk00z28

Forced to by choice
I've got a buddy with a 96 GT thats pushing 10lbs thru a procharger. He just now pulled a 13.5. :rolleyes:

Took FI on his car to beat my 13.6 in my stock Z28. :tdown: :D
 

Flyin Ryan

hated cuz he drives fords
blk00z28 said:
I've got a buddy with a 96 GT thats pushing 10lbs thru a procharger. He just now pulled a 13.5. :rolleyes:

Took FI on his car to beat my 13.6 in my stock Z28. :tdown: :D

he needs to learn how to shift a bit wouldn't you say
 

Drac0nic

New member
blk00z28 said:
I've got a buddy with a 96 GT thats pushing 10lbs thru a procharger. He just now pulled a 13.5. :rolleyes:

Took FI on his car to beat my 13.6 in my stock Z28. :tdown: :D

Damn, did he kill it half ways down the track? :rotf:
 

blk00z28

Forced to by choice
I dont know whats up with his car.

Well, I should say that. I know whats up with it. He took all the parts off of a rolled 96 GT, he was lucky that the parts wernt hurt in the accident of the other car. And he just bolted them on, no tune or nothing. Exhaust leak's everywhere.. Fauling out plugs left and right. I'm probably gonna go to another track this friday to get a better run in my car.

But if his car was running good, it should have no problems beating my car. :dunno:
 

Ground Rat

New member
Drac0nic said:
sy#276 said:
with a good driver that guy should see high 11s my stang went 11.50s stock bottom end all motor. i got a friend thats going 11.80s with out a dyno tune and ported ford explorer heads all motor stock bottom end. any ways a mid 12 sy took out my stang on the street up to 80 and it pulls the left front a half foot off the ground on the street im proud to say that though. cause simply syclones rule.

Explorer heads? My curosity is piqued. Nice K btw.

Explorer heads are also known as GT40P heads.
 

90stangGT

Cobra member
Ground Rat said:
Drac0nic said:
sy#276 said:
with a good driver that guy should see high 11s my stang went 11.50s stock bottom end all motor. i got a friend thats going 11.80s with out a dyno tune and ported ford explorer heads all motor stock bottom end. any ways a mid 12 sy took out my stang on the street up to 80 and it pulls the left front a half foot off the ground on the street im proud to say that though. cause simply syclones rule.

Explorer heads? My curosity is piqued. Nice K btw.

Explorer heads are also known as PI heads, PI standing for power improved.
PI heads are the revised cylinder head found on the 99-04 GT mustangs. The explorer heads come from 5.0L powered explorers that are supposed to be the same as iron GT-40 heads. IE cheap power from the junkyard.
 
Top