FUEL Tuning 101

JSM

Active member
Got spike of energy and decided to help some of the new guys understand tuning.

Tuning is by far the most under used tool available in enchancing both performance and safety with these trucks. I was victim myself to wanting to keep bolting on more parts to only go slower. I knew how to use wrenches, the tuning and electronic stuff was not comfortable to me so I avoided it. Was I wrong.

Tuning by far is the best bang for the buck. It is one of the reasons I have been able to get a stock turbo truck into the low 12 second range with ZERO internal engine mods. Look at some of the trucks with big turbo's mod lists 1 page long that run slower than this. Ever wonder why?

Tuning involves several items from spark plug gap, good condition wires, cap, rotor, tire pressure, what boost do you leave the line at, how much boost, etc. Tuning is MORE than just chip work.

Recently I have been asked by a number of people in how to get started with tuning so instead of writing 10 different emails I figured I would give my take on how I tune. Now someone else may have a different approach but this is what works for me.

In this section I will address Fuel tuning and how the main tables effect one another.

Homework: Download, print, study, memorize the P4 document. (link is on NWSTP.com) It is boring yes. It will tell you the logic behind what is going on within the ECM. It combined with understanding how an engine works and what air fuel ratio is critical.

In particular at least for this part study the fuel section. You will notice the final fuel formula is (http://www.nwstp.com/forum/P4_section_9.asp)

BPW = BPC * MAPP * T' * A/F' * VE * F33C * BLM * DFCO * DE * CLT * F77

It is now your job to study how each plays a part in the final pulse width of the injector. You will notice some of the items are labeled with an F followed by a #. This is the label given to certain tables. If you use promgrammer or tunerpro (with the definition files on nwstp) you will notice those labels correspond. Nice huh. (tunercat does not have the labels).

In the end their are 3 MAIN tables. They are F31E, F29, F30 and F77. (there are more but these are the main ones).

F31E: This table is the main VE for idle or 0% TPS. If your idle is rich or lean, not smooth this is the table to start with. It is also the table I suggest a new tuner play in as chances of engine damage here are minimal.

F29: Base VE -vs- RPM. This is the main fuel table for conditions that are NOT 0% TPS. Be careful here if you are new, you can do serious engine damage if your not careful. One thing to notice it only goes up to 4000 rpm and 100kPA (0psi). hmmm no boost fuel control here?? (we will come back to this)

F30: Base VE -vs- RPM. Small table, you will notice has nothing to do with boost and it applies to ALL running conditions. Changes here effect all fuel at that rpm level. This can be good and bad. Just note it will change fuel at that rpm everywhere. Notice that rpm is higher than 4000 here and goes to 6400. This is where you can adjust your high rpm fuel to some degree.

F77: Base boost multiplier. This is your main control for fuel under boost. Most people feel all the truck needs is tuning under boost, or want to tune boost first. Here is the problem using that logic. This is a multiplier. What happens is it takes the last value in the F29 table (most likely 4k rpm and 100kPA) and multiplies it by the value in F77. Now lets assume you dial in boost first, then notice you have some drivability issues. So you go back and adjust F29 table, or any of the other ones. Now you get back into boost and F77 multiplies by a new VE. BAM your boost fueling now is off also. Whenever I tune I get drivability dead on first. I will spend 99% of my time doing drivability, then last thing I do is boost fueling (usually I can get it with a couple boost runs). If you go the other way around you will be chasing your tail and flusterated.

You may notice I detailed out 4 tables, some exist in the main formula some are hidden within it. If you want to learn to tune, you need to learn how each plays a part.

Basically though the tables get added to each other. (simplifing things). So if the value in F29 is 30 and F30 is 23 and the multiplier at F77 is 1.1 we have

(30 + 23)*1.1 or 58.3% Volumetric Efficiency.

The next question most ask is how does VE = a pulse width.

If you got this far you should know that an engine likes to run at 14.7:1 AFR under cruise (not boost). So that is 14.7 parts air to 1 part fuel. The computer knows the size of the engine and how many cylinders. So it can figure out each cylinder is .71 liters in size, or it taking in .71 liters of air. So we must need .048 liters of fuel right? (.71/14.7). Almost. Engines don't run at 100% efficiency. Most NA motors run less than 100%. Most boosted motor under boost can run more than 100% VE. So in our example instead of .048 liters of fuel we need 58.3% of that or .028 liters of fuel. Computer knows size of injector (somewhat) so if an injector flows .028 liters per second in this example the injector should stay open .028 seconds.

Now keep in mind I have WAY oversimplied things here. But it gives you an idea. I know some flaws are in above logic compared to what our computer actually does, but my point is to let you understand basically what is going on.

If we increase VE then you can see more fuel will be injected into the engine, lower VE and less fuel. Pretty simple huh?

Word of caution. If you have off idle stumbles, bogs when accelerating, engine goes rich when slowing down chances are NON of the above changes will help much. The above tables are mainly for steady state driving not large changes in Kpa (boost), rpms, or throttle positions. That is for another section.

If this is helpful let me know and I will see what I can do about detailing acceleration and deceleration tuning. Although now that you have the p4 document the information is there for you. :hint:

Personal preference: I like to tune in open loop. This typically is switched on and off via Temp Thresh. For C/L Determination" (0x034A) out of range (151.6 degC max)." constant.

Some like to tune based on BLM and INT (get to study what those mean if you don't know). I prefer to go off the o2 (stock or wb) and not let the computer mess around with my VE #'s.
 
Last edited:

sytyguy

Moderated User
Re: FUEL Tuning 101

Great job Jeff....I know how labor intensive it is to explain all of this stuff, so kudos to you.
Ok.gif


Here are some links to explanations I made about tuning in the past. They can help compliment & reiterate what you wrote:

http://www.syty.net/forums/showthread.php?t=22996
http://www.syty.net/forums/showthread.php?t=8213
http://www.syty.net/forums/showthread.php?t=15287

There were other threads, but the board has moved them I guess. I'll keep searching for them.

Hood
 

Sy Guy 0024

Member
Re: FUEL Tuning 101

Not to swing on Jeff's nutsack, but OMG, this is the kinda post I've been looking for. I've had tunerpro for some time now, but have been afraid to do much with it because I didn't know where to even begin. This info will be VERY helpful to me and I'm sure many others. I've got a ton of mods on my truck and am only at 11.79 now. I think there's much room for improvement and I think it lies in additional tuning.

Thanks for sharing some of your knowledge Jeff. Gives me some direction to go now. I'd definitely be interested in reading more.

Corbin
 

JSM

Active member
Re: FUEL Tuning 101

This adds to my information above and might shed some light on tuning for alky injection.

sytyguy said:
For large fueling changes you'll prolly wanna do some work in all of the below maps:

F29 - Base Pulse VE vs RPM vs MAP
F30 - Base Pulse VS vs RPM
F31M - Base Pulse Inverse Air Temp vs ADMAT
F77 - Base Boost Multiplier vs MAP

Use F29 & F30 for fueling changes that affect all boost ranges. You may already know this, but F29 & F30 are added together to get a combined VE for open throttle conditions. Basically, a value from F30 is given based on RPM alone, then it's added to the corresponding RPM vs MAP cell data from F29. Obviously, F29 ends at 100 MAP and 4000 RPM, so any condition outside of this range (4000+ RPM and/or 100+ MAP) assumes the lower right-hand cell data (100 MAP & 4000 RPM).

Okay, with that outta the way, you may wish to do some tuning in F77. This is the only fuel multiplier we have based solely on boost. Wanna tune for high boost conditions w/o hacking up the VE tables?.....use F77. This table is pretty self-explanatory, just remember that it is a direct multiplier, so the higher the number, the higher the fuel delivery.

Now, F31M.....the most overlooked fueling table, and probably the one you'll wanna look at the most. F31M uses a BPW scalar based solely on MAT temp.....so you could have a reduction in fuel delivery based on a drop in MAT temps. Figure out the average MAT temp with and w/o alky and design the map around that data. Just make sure to give some fuel lead-in and lead-out, so that you don't have abrupt fueling spikes (could lead to rich/lean jumps that promote detonation, etc....). Also, keep in mind that this table uses Kelvin for the temp range, so be sure to convert the temp data before making changes.

I hope this sheds some light on the fueling structure of our trucks (there's A LOT more to it than this). You might wanna look up some of the big alky users out there to see their results, changes, etc....
 

JSM

Active member
Re: FUEL Tuning 101

More good notes to try to gather up all this information

sytyguy said:
F57 only needs to be changed if you want to modify the cold engine idle AFR. Works like this....if temp is below 0x0361 = 56 degC (132.8 degF) and the TPS is at 0% (idle) then F57 is used to calibrate an AFR dependent on coolant temp. If you move the TPS from idle during this condition (cold engine), then F57 is ignored and an AFR is calibrated from F56 based off of coolant temp and map. If temp rises about 0x0361, then the ECM will begin using the AFR at 0x0392 for stoich. Most Ultimate chips have C/L determination set around this point as well, so that the blm/int will be used at about the time the engine goes into warm engine AFR enable (although stock is 21.5 degC - 70.7 degF for C/L determination).

* All of this is covered in Section 9.1.4.3 in "The Document". Read up on it and it should answer most of your questions.

As far as tuning VE (AE & DE will still need to be tuned separately), since F30 does affect all (even though only a small portion of F29E is used that F30 affects), I like to do most of my cruise/idle VE modifying in F29 & F29E. You will use a lot of other tables for dialing in the whole fueling curve, but those 2 can get most of your idle/cruise dialed in. Funny you should ask this as I just got through doing some VE tuning on our '95 Silverado. Here's my example:......Condition - steady state cruise, rpm @ 1600, map at 60 kPa, BLM hovering around 117-118. The truck was getting poor gas mileage, so I really only wanted to modify this one area of the VE table (WOT & idle were fine). Open editor and see that VE in that cell is 84 (NA Silverado remember). Drop it 80, reburn it, and go for a drive. Fueling is better, but BLM is still low (121-122). Reopen editor, drop VE to 76, reburn, and go back out. Fueling is good now, BLM around 128 with a tendency for lean. Right where I wanted it. This might be a bit drastic of a change for your condition, but .5 changes are gonna take forever to get a noticeable improvement if it's off a good bit. Use changes of 2 or 3 to get it close then fine tune it. Best advice is to use as much clarity as possible (meaning stay out of conditions where EGR, AE, DE, etc... may be active). For cruise your rpm is usually gonna be between 1600 & 2200 and map between 50 kPa & 80 kPa. Put emphasis on those areas to modify cruise. (Idle rpm is usu around 700-900 with map around 40-50 kPa). Now, that was cruise/idle. To dial in WOT fueling there are a lot of factors to keep in mind. (AE, PE, etc...). This is gonna be a balance of a number of tables (F30, F29, F77, F61, & F31M). Each has it's own place, so use it accordingly. My advice, start rich and tune down. Don't wanna go lean @ 22 psi and 5000 rpms. WOT fueling has been covered by a lot of us in the past. Do a search and you should dig up some good info on what does what.

Lean spots can occur when you remove fuel in one spot and don't "smooth" out the table around it. For instance, the example above. I went from 84 to 76 in one cell in the VE Open table. This got the result I was looking for, but if I had just left it like that, I'd have had problems. Accelerating slightly out of that spot would have made a jump from 76 to 88 to the next cell. Pretty big jump for no real rpm/map change. There would have been a little bog and would have been noticeable when driving and in DM (int/blm around 128 and suddenly back to 117-118). I, in turn, smoothed out the rest of the table to "flow". This way you get a smooth transition from cell to cell. No big jumps or drops. You want to take this same mentality when editing the Main Spark Table.

To dial all of this in, I suggested it was best to use the blm/int as your friend and get close in C/L. Use whatever is easiest for you, but instead of just looking at the stock O2 readings while trying to drive and keep track of what was rich/lean, use C/L. Go for a run, record with DM, and come back and use the histogram to help you see where it was lean, where it was rich. Neither substitutes for a WBO2, but the blm/int will spot trends in rich/lean conditions, versus you trying to see what the O2 itself is doing (which isn't very accurate). Once you have it close, switch to O/L and tune for your truck from there. Your's may want a richer idle or cruise. You can address that in O/L. Like I said 14.7 isn't always best.
 

JSM

Active member
Re: FUEL Tuning 101

ACCELERATION ENRICHMENT

So you have steady state driving dialed in perfect right? If not don't even bother messing around here yet. Do keep in mind though, sometimes once you do play in these sections you may need to go back to previous tables. Tuning involves constant tweaking and changes in one area WILL effect others. For example if you change the timing watch what happens to fuel.

Go back to how a carb works. If you look a carb has an acceleration pump. What this does is as you move the throttle it injects extra fuel to help the motor get moving. Otherwise the motor will go lean, bog, etc.

Our ECM's have the same thing. In this case it is called acceleration enrichment.

There are 4 main tables. If you use tunerpro and the definitions I helped create listed on NWSTP you will notice these are all in 1 area labeled accerlation. Imagine that. :lol:

PE we will discuss later so ignore it for now.

The 4 tables are

AE - DELTA MAP CONTRIB VS DELTA MAP

For those that didn't take physics or other related classes Delta = change. So this table is CHANGE in Vacuum (boost) The changes are 0, 10, 20, 30 and 40 kPA

So for example you have a CHANGE of 20kpa the ecm will command an extra bit of fuel equal to what is in the table. Stockish chips are around 300mSec. So if you notice as map changes engine goes lean or rich you may want to play around here.

AE - DELTA THROTTLE CONTRIB VS DELTA TPS

Does the same thing as above but in this case it is changes in throttle.

RPM MULTIPLIER FOR ACCEL ENRICHMENT

This multiplies the above depending on RPM. If you have good acceleration at low rpm, but at high rpm it goes lean or rich this is where a change should happen.

AE TEMP. CORRECTION FACTOR VS COOLANT TEMP

I cold engine will need more fuel than a warm engine. This table corrects for that.

Again, make sure normal steady state driving is good also. If you have a lean or rich condition due to a table being wrong, you will be fighting yourself trying to cover it up with these.
 

Robert Lone

MUTANT
Re: FUEL Tuning 101

Hey Jeff,

Great thread!!! Two thumbs up!!!

BTW...I really like the new avitar! Where did you get what's in the pic?:)
 

James Thomas

"NO CLASS"
Re: FUEL Tuning 101

T-56 said:
Hey Jeff,

Great thread!!! Two thumbs up!!!

BTW...I really like the new avitar! Where did you get what's in the pic?:)



My :2cents: , this thread should be finished (err, as close as can be) and put in the vault!
_____________
James Thomas
 

Loeryder

New member
Re: FUEL Tuning 101

NICE!
Keep right on typing...

Right click Copy, right click paste...

Thanks for bringing all this stuff ot the surface guys.
Now if only I was unemployed I'd have neough time to actually work on mine.
Oh wait then Id be poor...
 

JSM

Active member
Re: FUEL Tuning 101

Deceleration Enleanment (DE)

This is almost opposite of AE. This situation occurs are you get off the gas. When you get off the gas obviously fueling changes and much less is needed. Although the ECM will know that you are now at a high vacuum (20-30ish kPA), that fueling alone is not enough as you just dumped a bunch into the cylinders just before you let off.

What these tables do overall is short term turn or limit fuel during a deceleration condition.

What can happen if it is wrong is the truck will go overly rich or lean, possibly killing the engine or a bog on a accel/cruise shortly after a decel.

Again 4 tables exist that match AE, that work the same but instead of giving extra fuel, shut the fuel off.
 
Re: FUEL Tuning 101

Wow, this has really shed some light for me. Thanks for the writeup, bu ti di have one question, about setting the AFPR, with the vac line removed and the engine at idle, what shoud the pressure be, and then what kind of pressure should i have at idle with the vac line connected.

Im running a big overkill aeromotive A1000 external pump on a sumped stock tank and at idle with vac line connected in right at 40PSI, and with it removed it at 47-49 PSI, and i have the stock FPR not an aftermarket adjustble one, and mine runs pretty rich and my gas milage sucks bad, i get around 12 MPG at best, and that driving it like an old lady and not getting into boost.
 

JSM

Active member
Re: FUEL Tuning 101

Think of FUEL pressure and making adjustments to it as changing ever so slightly the size of the injector.

Within reason you can tune for any fuel pressure. Somewhat.

They key here is what FP was the chip dialed in at. If you brought a truck to a tuner with the FP at 40psi, he dials it in, you go home and up the FP to 42 would you expect it to run just as well? Probably not.

The 3bar stock injector chips are setup and tuned to run higher FP. This is to help make the stock injector larger and have more capability.

The 50's general are tuned back down at stockish FP level.

Adjustment to FP will change EVERY part of the fuel table. You can't fix a bad tune with FP adjustments. You can't ruin one with it though.

The key here is to tune with the same FP. The only way to get a consitant reading of FP is with the vacuum line removed. Sure I could say here is the perfect chip turn your fp to 35 with the vacuum line on. Problem is where does your truck idle. The idle vacuum is very unstable. So on tuesday at idle your FP is 35, Wednesday it is 36, and the 3rd thursday of the month it is 34.

If you remove the vacuum line the regulator see atmosphere. Which is way more stable than your truck idling.

So if you are getting craptastic gas mileage it MIGHT be the FP. It could be your combination of parts though that don't match the chip you have. (did you port your heads EXACTLY like the tuners truck?). Same cam? Same turbo, same intake? Close is just that close.
 

ashman

------
Re: FUEL Tuning 101

A request for a future "how to"...how to read data with Tunerpro... I know this is your tuning tool of choice. Could you share some to the ways you extract/decipher data? It is SO different from DM and doesn't appear to be user friendly at all.
 

JSM

Active member
Re: FUEL Tuning 101

I will be glad to give some pointers but a bit confused how tunerpro's aldl stuff isn't very user friendly.

Of course being it does more than scan you gotta learn that button or drop down window.

4 big letters on top show D for dash, M for monitor, F for Flags, V for Value.

In the dash you can right click select any value you want displayed.

Being it is natural to use for me, just need more specifics on what is confusing for others.
 

ashman

------
Re: FUEL Tuning 101

i guess my main complaint is the way that the data is displayed or a lack thereof.

with DM, after a run your presented with 4 graphs, of your choosing, of the entire run. you can pretty easily pickout where problem spots are visually, drag a selection box around that area and see the just that area and see all of the data change as you move your cursor around.

whereas, with TP, you've got to 'PLAY' the run back and pause and use you arrow keys to go forward and back, and if you click off of the little slider bar, the keys loose direction focus.

and, you can't see the graph and the aldl value at the same time.

and, with the "aldl values" screen showing you have an enormous unused white space to the right that could be used for so much more like, being able to see all of the values on one screen, at one time, without scrolling up and down.

obviously, with the developement you guys are doing with the $58, TP will be the standard for tuning shortly, so i guess we'll have to learn but i just wish it were more intuitive, like DM.

then again, maybe i need to RTFM
icon_redface.gif


sorry for the rant...off the box...
 

JSM

Active member
Re: FUEL Tuning 101

i will agree the graphing is not as nice. I asked the auther his advice was you can output to excel via csv easy and graph there, as he would rather spend time developing for hardware stuff not a lot of time on the good looks if it can be done easy another way. I partially agree.
 

sy#2921

BAMF
Re: FUEL Tuning 101

I didnt know you could export TP to excel, what that being know yeah its a little effort but that makes it just as good as DM providing you know how to make a graph in excel
 
Top