b-rad420247
Member
Can someone take a look at my file and explain what is going on....I'll send the file by email.
Thanks
Thanks
Last edited:
Data log file help( aldldroid)
- Thread starter b-rad420247
- Start date
Eric Sy GN
Donating Member
Re: Data log file help( aldldroid)
You can email me the file, eric@turbotweak.com
What are you seeing?
You can email me the file, eric@turbotweak.com
What are you seeing?
b-rad420247
Member
Re: Data log file help( aldldroid)
Sent ....truck keeps spitting a little a wot
Sent ....truck keeps spitting a little a wot
b-rad420247
Member
Re: Data log file help( aldldroid)
Did you get ?
Did you get ?
Eric Sy GN
Donating Member
Re: Data log file help( aldldroid)
Yes, but could you send the tunerpro format, not csv.
Yes, but could you send the tunerpro format, not csv.
b-rad420247
Member
Re: Data log file help( aldldroid)
Which would be the tunerpro format
Which would be the tunerpro format
WyoSyclone
Active member
IGottaSy
Active member
Re: Data log file help( aldldroid)
The developer is a super nice dude. His contact info should be displayed somewhere in the app. Or I can get it for you if you need it. He welcomes feedback to help improve on this, Very cool.
The developer is a super nice dude. His contact info should be displayed somewhere in the app. Or I can get it for you if you need it. He welcomes feedback to help improve on this, Very cool.
b-rad420247
Member
Re: Data log file help( aldldroid)
Did I send the right file this time Eric? My mods are in my signature
Did I send the right file this time Eric? My mods are in my signature
Eric Sy GN
Donating Member
Re: Data log file help( aldldroid)
I got it. I see a little bit of knock retard at WOT, 2-3*. I would reduce timing a degree or two to see if that helps. It's also a bit rich for your boost level, 10.8 AFR at 13psi. I see you are running it in closed loop WOT. What AFR are you commanding? The correction is bottomed out, so you need to reduce WOT fuel a bit. I would try to target more like 11.2-11.5 AFR and see how it does.
If none of that helps, then you might have an ignition issue.
I got it. I see a little bit of knock retard at WOT, 2-3*. I would reduce timing a degree or two to see if that helps. It's also a bit rich for your boost level, 10.8 AFR at 13psi. I see you are running it in closed loop WOT. What AFR are you commanding? The correction is bottomed out, so you need to reduce WOT fuel a bit. I would try to target more like 11.2-11.5 AFR and see how it does.
If none of that helps, then you might have an ignition issue.
b-rad420247
Member
Re: Data log file help( aldldroid)
Ya running closed loop....should I have my chips open loop switch turned on? Can I change the timing and fuel with the parameters on the chip ?
Ya running closed loop....should I have my chips open loop switch turned on? Can I change the timing and fuel with the parameters on the chip ?
Eric Sy GN
Donating Member
Re: Data log file help( aldldroid)
No, you don't need to change the dip switch settings.
You can change fuel and timing with the chip parameters. Base WOT fuel you can reduce by turning down the WOT fuel dial on the chip.
No, you don't need to change the dip switch settings.
You can change fuel and timing with the chip parameters. Base WOT fuel you can reduce by turning down the WOT fuel dial on the chip.
b-rad420247
Member
Re: Data log file help( aldldroid)
So with my fuel being at 10.8 at 13 psi....should I adjust the wot fuel dial or adjust parameter settings?
So with my fuel being at 10.8 at 13 psi....should I adjust the wot fuel dial or adjust parameter settings?
Eric Sy GN
Donating Member
Re: Data log file help( aldldroid)
I would use the dial first, since it's permanent and can't be lost if the ECM loses power.
But, to be clear, you are adjusting it because the correction is bottomed out, not because the AFR is 10.8. You need to define a target AFR, then adjust the fuel until the correction is close to zero (give or take), so that the computer can achieve the target.
I would use the dial first, since it's permanent and can't be lost if the ECM loses power.
But, to be clear, you are adjusting it because the correction is bottomed out, not because the AFR is 10.8. You need to define a target AFR, then adjust the fuel until the correction is close to zero (give or take), so that the computer can achieve the target.
b-rad420247
Member
Re: Data log file help( aldldroid)
Sent a couple more files done today......it's feeling better..... I have parameter 7 set to 110 on scantmasterg....also what do I look at to maintain correction close to zero?
Sent a couple more files done today......it's feeling better..... I have parameter 7 set to 110 on scantmasterg....also what do I look at to maintain correction close to zero?
Last edited:
