Recent content by RiceEater

Re: Running super rich Ok I got the O2 sensor changed, I did like someone else said and bashed off the top of the sensor and then just put a regular socket on it and it came right off. My TY seems !00% better now. I still have a RPM flux, but now it is much smoother only about 600 to 750 no...

Re: Running super rich Ok well got the temp fixed. I dropped down the ecm and found a loose wire. Now I have the problem that my 02 mv in open loop drop all the way to 0 then spike to 860 then drop to 0 over and over. I think my 02 sensor is fried. I wanted to pull it out and check it out...

Re: Running super rich Yes I'm on the right one, the one next to the heater hose and the 2 wires. I shorted the wire with a paperclip and the temp stayed the same.

Re: Running super rich Ok so after some testing, even if I unplug the temp sensor with the motor warm it says -37.8. I tested the wires after the connector and it still shows 10 ohm. with the sensor on (not in the motor) it drops to 2 ohm. Is any of this right/wrong? I'm about to dive into...

Ok so my 92 TY has been running richer and richer so I stopped driving it for a few months till I could figure it out, and now this is what I have. In the last 2 weeks it has started throwing code 45 rich while driving, and starting to run like crap. This went on for about a week and now it...

Re: Help no fuel pump prime!FIXED Re: Help no fuel pump prime!FIXED Well after some more looking I found only 1/2 of my ecmb fuse had power. I started pulling off all my caps and found 1/2 of the pink wire from the ign switch had broken wires and was not getting contact. Patched it up and it...

Re: Help no fuel pump prime! Now that I look at it I get no lights in the dash when I put the key forward. No eng or check guage or anything. Also ecmb has 12 power with key off and but i checked ecm next to it and it has no power with the key in off start or run, I guess this is my problem...

Re: Help no fuel pump prime! swapped em, no dice. Still no prime action. Has to be something under the dash I messed with. Does the ign switch on the column have anything to do with this? Thats about the only thing I messed with that gave me any problems.

Ok I have been installing a remote start in my 92ty today. I got it all hooked up and went to crank it with the remote and it wouldn't start. It will crank but no start. I then used the key and still no start. Then I noticed the fuel pump is not running nor will it prime. ecmb fuse is stll...

Well I was on my way home from work the other day and my friend I work with was behind me. I decided to get on it and dust him (and I did) but after he told me that evertime my typhoon would shift it would let out a little puff of black smoke. Now I haven't done anything to the motor yet but I...

Re: Ostrich HELP! OK just to update I got the g1 adaptor and it fixed all my problems. Now time to start the hard part!

Re: Ostrich HELP! Ok i ordered the g1 adaptor, will post if it fixed the problem. (i bet it will)

Re: Ostrich HELP! Ok I found my problem I have some loose pins. I know they got messed up when I pulled the old memcal out. Can I get new pins for the sockets? If I could get some pins I could solder it in place

Re: Ostrich HELP! Thank you so much! that really helps. I take it the adaptor doesn't flip it or anything just make it connect better

Re: Ostrich HELP! Ok it sounds like i'm being told 2 different things. One said to make sure the ribbon cable when in to the rest of the pcm (puts the red stripe on the inside of the zif) and the other said to make sure the red stripe was on the outside (would make to go out to the edge) does...